Epson Moverio BT-200 (epson-embt2ws): Difference between revisions
more status update |
add manufacturer to codename |
||
(One intermediate revision by one other user not shown) | |||
Line 2: | Line 2: | ||
| manufacturer = Epson <!-- e.g. HTC --> | | manufacturer = Epson <!-- e.g. HTC --> | ||
| name = Moverio BT-200 | | name = Moverio BT-200 | ||
| codename = embt2ws <!-- e.g. htc-bravo --> | | codename = epson-embt2ws <!-- e.g. htc-bravo --> | ||
| image = File:embt2ws.jpg | | image = File:embt2ws.jpg | ||
| imagecaption = CHANGE_ME | | imagecaption = CHANGE_ME | ||
Line 18: | Line 18: | ||
<!-- the following status_* questions should be answered with Y for yes, P for partial, N for no, - for N/A or unavailable, or left blank for untested or unknown --> | <!-- the following status_* questions should be answered with Y for yes, P for partial, N for no, - for N/A or unavailable, or left blank for untested or unknown --> | ||
| status_usbnet = Y | | status_usbnet = Y | ||
| status_emmc = Y | |||
| status_flashing = <!-- Flashing with "pmbootstrap flasher" works? Put Y here. It works the same for everything coming below. --> | | status_flashing = <!-- Flashing with "pmbootstrap flasher" works? Put Y here. It works the same for everything coming below. --> | ||
| status_touch = <!-- Touch screen is working? You can also answer these questions with P for partially. --> | | status_touch = - <!-- Touch screen is working? You can also answer these questions with P for partially. --> | ||
| status_screen = <!-- The display is working? --> | | status_screen = <!-- The display is working? --> | ||
| status_wifi = Y <!-- Wireless network works? --> | | status_wifi = Y <!-- Wireless network works? --> | ||
Line 25: | Line 26: | ||
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? --> | | status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? --> | ||
| status_mainline = Y | | status_mainline = Y | ||
| status_battery = <!-- Charging the battery with charging-sdl is possible --> | | status_battery = N<!-- Charging the battery with charging-sdl is possible --> | ||
| status_3d = <!-- Hardware accelerated 3D graphics (e.g. with freedreno) --> | | status_3d = <!-- Hardware accelerated 3D graphics (e.g. with freedreno) --> | ||
| status_audio = <!-- Using the device's speakers/headphone jack works --> | | status_audio = Y<!-- Using the device's speakers/headphone jack works --> | ||
| status_bluetooth = P <!-- It's possible to pair and use other devices via the bluetooth protocol --> | | status_bluetooth = P <!-- It's possible to pair and use other devices via the bluetooth protocol --> | ||
| status_camera = <!-- Taking photos and videos works. --> | | status_camera = N<!-- Taking photos and videos works. --> | ||
| status_gps = P <!-- The Global Positioning System sensor works. --> | | status_gps = P <!-- The Global Positioning System sensor works. --> | ||
| status_mobiledata = <!-- Connecting to the Internet via cellular network. --> | | status_mobiledata = - <!-- Connecting to the Internet via cellular network. --> | ||
| status_sms = <!-- Sending and receiving short messages works as intended. --> | | status_sms = -<!-- Sending and receiving short messages works as intended. --> | ||
| status_calls = <!-- Talking to other people over the cellular network. --> | | status_calls = -<!-- Talking to other people over the cellular network. --> | ||
| status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" --> | | status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" --> | ||
| status_otg = <!-- USB-OTG adapters work, e.g. to connect an USB flash drive to the device --> | | status_otg = <!-- USB-OTG adapters work, e.g. to connect an USB flash drive to the device --> | ||
| status_nfc = <!-- Near-Field Communication (NFC) works --> | | status_nfc = -<!-- Near-Field Communication (NFC) works --> | ||
| status_usba = <!-- Full-sized USB-A port works (Usually applicable to SBCs and laptops) --> | | status_usba = -<!-- Full-sized USB-A port works (Usually applicable to SBCs and laptops) --> | ||
| status_hdmidp = <!-- Video and audio output with HDMI or DisplayPort works --> | | status_hdmidp = -<!-- Video and audio output with HDMI or DisplayPort works --> | ||
| status_keyboard = <!-- Keyboard works (Mark "-" if device doesn't have a keyboard) --> | | status_keyboard = <!-- Keyboard works (Mark "-" if device doesn't have a keyboard) --> | ||
| status_touchpad = <!-- Touchpad works (Usually applicable to laptops) --> | | status_touchpad = <!-- Touchpad works (Usually applicable to laptops) --> | ||
| status_irtx = <!-- Infrared (IR) port works --> | | status_irtx = -<!-- Infrared (IR) port works --> | ||
| status_trustzone = <!-- TrustZone works --> | | status_trustzone = <!-- TrustZone works --> | ||
| status_accel = Y | | status_accel = Y | ||
Line 48: | Line 49: | ||
| status_proximity = <!-- Proximity sensor works --> | | status_proximity = <!-- Proximity sensor works --> | ||
| status_hall = <!-- Hall effect sensor works --> | | status_hall = <!-- Hall effect sensor works --> | ||
| status_barometer = <!-- Barometer works --> | | status_barometer = -<!-- Barometer works --> | ||
| status_powersensor = <!-- Power sensor works --> | | status_powersensor = <!-- Power sensor works --> | ||
| status_fossbootloader = <!-- Device has a free and open source bootloader --> | | status_fossbootloader = <!-- Device has a free and open source bootloader --> |
Latest revision as of 06:43, 8 June 2024
![]() CHANGE_ME | |
Manufacturer | Epson |
---|---|
Name | Moverio BT-200 |
Codename | epson-embt2ws |
Released | 2014 |
Type | glasses |
Hardware | |
Chipset | TI OMAP 4460 |
CPU | 2x1.2 GHz Cortex A9 |
GPU | PowerVR SGX540 |
Display | 960x540 see through glasses |
Storage | 8GB eMMC + uSD slot |
Memory | 1024 MB |
Architecture | armv7 |
Software | |
Original software | Android |
Original version | 4.04 (Kernel 3.0.21, U-Boot 1.1.4) |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | yes |
Flashing |
No data |
---|---|
USB Networking |
Works |
Internal storage |
Works |
SD card |
No data |
Battery |
Broken |
Screen |
No data |
Keyboard |
No data |
Touchpad |
No data |
Multimedia | |
3D Acceleration |
No data |
Audio |
Works |
Camera |
Broken |
Camera Flash |
No data |
Connectivity | |
WiFi |
Works |
Bluetooth |
Partial |
GPS |
Partial |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
Sensors | |
Accelerometer |
Works |
Magnetometer |
Works |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Power Sensor |
No data |
This device is based on the TI OMAP 4460. See the SoC page for common tips, guides and troubleshooting steps |
Contributors
- Andi
Users owning this device
How to influence/change boot order
Boot order is eMMC, USB, UART, uSD. That can be overwritten by software until the next cold boot: Commands in U-Boot, similar could be done via /dev/mem
mw.l 0x4A326A0C 0xCF00AA01 mw.l 0x4A326A10 0xC mw.w 0x4A326A14 0x0 mw.w 0x4A326A16 0x43 mw.w 0x4A326A18 0x45 mw.w 0x4A326A1A 0x05 mw.w 0x4A326A1C 0x0 mw.w 0x4A326A1E 0x0 mw.l 0x4A326A00 0x4A326A0C
and then warm-reboot (e.g. reset button or reset command in newer u-boots).
If you want to reorder the boot order temporarily, you can do that from the original system if it is rooted, use setup-bootchoice from https://github.com/akemnade/bt200tools.
eMMC boot can be skipped using a 470 Ohm resistor from eMMC DAT 0 to GND on powerup. So that
would be a recovery if loader on eMMC is broken.
Accessing serial console in original system
JP1 (soldering jumper on the back side = gpio-138) needs to be shorted to enable serial console on factory kernel/u-boot. (4 2.54mm pitched holes). Voltage level is 1.8V
Boot process of the original system
Xloader is located at sector 256 and loads U-Boot from sector 512 as a raw headerless binary on the same device as Xloader also was loaded from. CONFIG_SYS_TEXT_BASE of such a u-boot has te be set to 0x80e80000. Size limit is 0x60000 bytes.
Factory U-Boot tries to load a sdboot.scr from the first partition (which must bet FAT) of the uSD card which is executed if the md5sum of the first line is 92b12a37d1913ac41d2956120a475aca, if not, normal boot from eMMC is done. Fastboot can be activated via commandline.
How to enter flash mode
Installation
System can be installed on uSD card. To be able to boot that you need to either:
- zero the xloader and u-boot area of the eMMC (after doing a backup)
- hack the integrated u-boot bootcmd to ignore check_code test results to boot the sdboot.scr (e.g. via usb mass storage mode via ums command): there is some
checkcode; if test $? -eq 1
in the builtin u-boot env, replace that by e.g.checkcode; if test 33 -eq 1
- use one of the methods to temporarily change boot order
- use u-boot commandline to manually load stuff (which can also be a modern u-boot, see u-boot wiki)
See also
- Factory kernel
- [1] branch epson-6.1, mainling attempts (look also at the corresponding wiki)
- [2] branch v2022.10-epson u-boot mainling attempts (look also at the corresponding wiki)