Lark FreeMe 70.2S (lark-freeme-70-2s): Difference between revisions
Appearance
JuniorJPDJ (talk | contribs) mNo edit summary |
m clean up |
||
Line 1: | Line 1: | ||
{{Infobox device | {{Infobox device | ||
| manufacturer = | | manufacturer = Lark | ||
| name = | | name = FreeMe 70.2S | ||
| codename = lark-freeme-70-2s | | codename = lark-freeme-70-2s | ||
| image = File:lark-freeme-70-2s.jpg | | image = File:lark-freeme-70-2s.jpg | ||
Line 14: | Line 14: | ||
| memory = 512 MB | | memory = 512 MB | ||
| architecture = armv7 | | architecture = armv7 | ||
| status_usbnet = | |||
| status_usbnet = | | status_flashing = | ||
| status_flashing = | | status_touch = | ||
| status_touch = | | status_screen = | ||
| status_screen = | | status_wifi = | ||
| status_wifi = | | status_xwayland = | ||
| status_xwayland = | | status_fde = | ||
| status_fde = | | status_mainline = | ||
| status_mainline = | | status_battery = | ||
| status_battery = | | status_3d = | ||
| status_3d = | | status_accel = | ||
| status_accel = | | status_audio = | ||
| status_audio = | | status_bluetooth = | ||
| status_bluetooth = | | status_camera = | ||
| status_camera = | | status_gps = | ||
| status_gps = | | status_mobiledata = | ||
| status_mobiledata = | | status_sms = | ||
| status_sms = | | status_calls = | ||
| status_calls = | | status = | ||
| status = | | booting = no | ||
| booting = no | |||
| pmoskernel = 3.x.x | | pmoskernel = 3.x.x | ||
| whet_dhry = 0.0 | | whet_dhry = 0.0 | ||
Line 67: | Line 66: | ||
== Booting == | == Booting == | ||
Put your sdcard inside tablet and it turn on. U-Boot screen should show up and boot should proceed. | Put your sdcard inside tablet and it turn on. U-Boot screen should show up and boot should proceed. | ||
Revision as of 14:38, 23 March 2021
This device is marked as not booting.
CHANGE_ME CHANGE_ME | |
Manufacturer | Lark |
---|---|
Name | FreeMe 70.2S |
Codename | lark-freeme-70-2s |
Released | 2012 |
Hardware | |
Chipset | [[Allwinner A10]] |
CPU | 1x 1.0GHz Cortex-A8 |
GPU | Mali-400 MP |
Display | 800x480 |
Storage | 4 GB |
Memory | 512 MB |
Architecture | armv7 |
Software | |
Original software | Android 2.3 |
postmarketOS | |
Category | testing |
Pre-built images | no |
postmarketOS kernel | 3.x.x |
Unixbench Whet/Dhry score | 0.0 |
Contributors
Maintainer(s)
How to enter flash mode
Flashing postmarketOS to NAND memory inside this device is not supported.
Installation
Just flash it on sdcard using pmbootstrap:
$ pmbootstrap install --sdcard /dev/YOUR_SDCARD_DEVICE
eg.
$ pmbootstrap install --sdcard /dev/mmcblk0
Booting
Put your sdcard inside tablet and it turn on. U-Boot screen should show up and boot should proceed.