Xunlong Orange Pi 3 (xunlong-orangepi3): Difference between revisions
m FIXUP |
mNo edit summary |
||
Line 38: | Line 38: | ||
| n-android = ✔ | | n-android = ✔ | ||
| pmoskernel = | | pmoskernel = Mainline | ||
| whet_dhry = 1455.9 | | whet_dhry = 1455.9 | ||
}} | }} | ||
Line 53: | Line 53: | ||
== Installation == | == Installation == | ||
Follow the [[Installation_guide]], use sdcard method. Then insert microSD into TF-card slot and plug the power cable, pmOS should boot. If not, try once again (on cold boot SPL sometimes decides there is 4096 MiB of RAM and boot hangs). | Follow the [[Installation_guide]], use sdcard method. Then insert microSD into TF-card slot and plug the power cable, pmOS should boot. If not, try once again (on cold boot SPL sometimes decides there is 4096 MiB of RAM and boot hangs). | ||
To install to eMMC, flash ondev to SD or run pmbootstrap from present pmOS installation on SD. | |||
== Serial console == | == Serial console == |
Revision as of 13:21, 16 July 2021
![]() Orange Pi 3 with UART connected | |
Manufacturer | Xunlong |
---|---|
Name | Orange Pi 3 |
Codename | xunlong-orangepi3 |
Released | 2019 |
Hardware | |
Chipset | Allwinner H6 |
CPU | 4x 1.8 GHz ARM Cortex-A53 |
GPU | Mali T720 MP2 600 MHz |
Display | HDMI port |
Storage | 8 GB eMMC (or empty slot) + microSD |
Memory | 1/2 GiB |
Architecture | aarch64 |
Software | |
Original software | BSP Linux 4.9 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | yes |
postmarketOS kernel | Mainline |
Unixbench Whet/Dhry score | 1455.9 |
USB Networking |
Works |
---|---|
Internal storage |
No data |
SD card |
No data |
Screen |
Works |
Multimedia | |
3D Acceleration |
Works |
Audio |
Partial |
Camera Flash |
No data |
Connectivity | |
WiFi |
Works |
Bluetooth |
Works |
Miscellaneous | |
FDE |
No data |
USB OTG |
Partial |
HDMI/DP |
No data |
Sensors | |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
Maintainer(s)
Users owning this device
- Exkc (Notes: toy found in store (no power brick))
Installation
Follow the Installation_guide, use sdcard method. Then insert microSD into TF-card slot and plug the power cable, pmOS should boot. If not, try once again (on cold boot SPL sometimes decides there is 4096 MiB of RAM and boot hangs).
To install to eMMC, flash ondev to SD or run pmbootstrap from present pmOS installation on SD.
Serial console
See linux-sunxi wiki page, connect your USB-UART adapter's RX to board's TX and vice versa.
OTG
As said in board's DTS,
/*
* This board doesn't have a controllable VBUS even though it
* does have an ID pin. Using it as anything but a USB host is
* unsafe.
*/
So you can't connect it to a PC via microUSB (but you still can use type A to type A cable). However, connecting microUSB devices such as flash drive may work, but untested because microUSB is too near to AC, so most devices can't be connected.
Audio
Hardware codec isn't supported in Linux kernel yet, so audio jack output won't work. However, HDMI audio works.
See also
- linux-sunxi wiki page
- pmaports!2268 Initial merge request