Jump to content

F(x)tec Pro1(x) (fxtec-qx1000): Difference between revisions

From postmarketOS Wiki
Danct12 (talk | contribs)
m Danct12 moved page F(x)tec Pro1 (fxtec-pro1) to F(x)tec Pro1(x) (fxtec-qx1000): There are Pro1 and Pro1X with MSM8998, and so we move the wiki page to a different name to make sure people won't install it on the new SDM662 Pro1.
Danct12 (talk | contribs)
No edit summary
Line 1: Line 1:
{{note|There are two model of the F(x)tec Pro1, one with MSM8998 and one with SDM662. This page is for MSM8998 Pro1 devices.}}
{{Infobox device
{{Infobox device
| manufacturer = F(x)tec
| manufacturer = F(x)tec
| name = Pro1
| name = Pro1(X)
| codename = fxtec-pro1
| codename = fxtec-qx1000
| image = File:fxtec-pro1.jpg
| image = File:fxtec-pro1.jpg
| imagecaption =  
| imagecaption =  
Line 10: Line 11:
| cpu = 4x 2.45GHz Kryo 280 Gold + 4x 1.9GHz Kryo 280 Silver
| cpu = 4x 2.45GHz Kryo 280 Gold + 4x 1.9GHz Kryo 280 Silver
| gpu = Adreno 540
| gpu = Adreno 540
| storage = 128 GB
| storage = 128/256 GB
| display = 1080 x 2160 AMOLED
| display = 1080 x 2160 AMOLED
| memory = 6 GB
| memory = 6/8 GB
| architecture = aarch64
| architecture = aarch64
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) -->
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) -->
| status_usbnet = <!-- USB networking does work? then put Y here and delete this comment -->
| status_usbnet = Y
| status_flashing = <!-- Flashing with "pmbootstrap flasher" works? Put Y here. It works the same for everything coming below. -->
| status_flashing = Y
| status_touch = <!-- Touch screen is working? You can also answer these questions with P for partially. -->
| status_touch = P
| status_screen = <!-- The display is working? -->
| status_screen = Y
| status_wifi = <!-- Wireless network works? -->
| status_wifi = Y
| status_xwayland = <!-- Showing X11 applications in a Wayland compositor (Weston, KWin, ...) works? -->
| status_xwayland = <!-- Showing X11 applications in a Wayland compositor (Weston, KWin, ...) works? -->
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? -->
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? -->
| status_mainline = <!-- Instead of a Linux kernel fork, it is possible to run mainline. -->
| status_mainline = Y
| status_battery = <!-- Charging the battery with charging-sdl is possible -->
| status_battery = <!-- Charging the battery with charging-sdl is possible -->
| status_3d = <!-- Hardware accelerated 3D graphics (e.g. with freedreno) -->
| status_3d = Y
| status_accel = <!-- The sensor that measures proper acceleration works -->
| status_accel = <!-- The sensor that measures proper acceleration works -->
| status_audio = <!-- Using the device's speakers/headphone jack works -->
| status_audio = <!-- Using the device's speakers/headphone jack works -->
Line 33: Line 34:
| status_sms = <!-- Sending and receiving short messages works as intended. -->
| status_sms = <!-- Sending and receiving short messages works as intended. -->
| status_calls = <!-- Talking to other people over the cellular network. -->
| status_calls = <!-- Talking to other people over the cellular network. -->
| status_irtx = -
| status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" -->
| status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" -->
| booting = yes <!-- The device is booting at all, can be yes/no *IMPORTANT* -->
| booting = yes


<!-- you can also use these lines if you need to:
<!-- you can also use these lines if you need to:
Line 50: Line 52:
== Contributors ==
== Contributors ==
* NotKit
* NotKit
* Danct12


== Maintainer(s) ==
== Maintainer(s) ==
Line 59: Line 62:


== How to enter flash mode ==
== How to enter flash mode ==
- Fastboot: While device is powered off, hold down the volume down key and hold down the power button.
- Recovery: While device is powered off, hold down the volume up key and hold down the power button.


== Installation ==
== Installation ==
Line 65: Line 70:
== See also ==
== See also ==
* {{MR|811|pmaports}} Initial merge request (closed, not merged)
* {{MR|811|pmaports}} Initial merge request (closed, not merged)
* {{MR|2984|pmaports}} Second attempt, now using mainline kernel.

Revision as of 16:37, 12 March 2022

Note There are two model of the F(x)tec Pro1, one with MSM8998 and one with SDM662. This page is for MSM8998 Pro1 devices.
F(x)tec Pro1(X)
Manufacturer F(x)tec
Name Pro1(X)
Codename fxtec-qx1000
Released 2019
Hardware
Chipset Qualcomm MSM8998 Snapdragon 835
CPU 4x 2.45GHz Kryo 280 Gold + 4x 1.9GHz Kryo 280 Silver
GPU Adreno 540
Display 1080 x 2160 AMOLED
Storage 128/256 GB
Memory 6/8 GB
Architecture aarch64
Software
Original software Android 9.0
postmarketOS
Category testing
Pre-built images no
Mainline yes
Features
Flashing
Works
USB Networking
Works
Internal storage
No data
SD card
No data
Battery
No data
Screen
Works
Touchscreen
Partial
Multimedia
3D Acceleration
Works
Audio
No data
Camera
No data
Camera Flash
No data
Connectivity
WiFi
Works
Bluetooth
No data
GPS
No data
NFC
No data
Modem
Calls
No data
SMS
No data
Mobile data
No data
Miscellaneous
FDE
No data
USB OTG
No data
HDMI/DP
No data
Sensors
Accelerometer
No data
Magnetometer
No data
Ambient Light
No data
Proximity
No data
Hall Effect
No data
Haptics
No data
Barometer
No data


Contributors

  • NotKit
  • Danct12

Maintainer(s)

Users owning this device


How to enter flash mode

- Fastboot: While device is powered off, hold down the volume down key and hold down the power button. - Recovery: While device is powered off, hold down the volume up key and hold down the power button.

Installation

See also