Jump to content

Samsung Galaxy Grand Prime Plus (samsung-grandpplte): Difference between revisions

From postmarketOS Wiki
Tooniis (talk | contribs)
Change arch
Tags: mobile edit mobile web edit
Tooniis (talk | contribs)
Status: Update touchscreen and i2c device status
Line 143: Line 143:
| Bosch BMA254
| Bosch BMA254
| N
| N
| Needs I<sup>2</sup>C support.
|
|-
|-
|Proximity Sensor
|Proximity Sensor
| Sharp GP2AP070S00F
| Sharp GP2AP070S00F
| N
| N
| Needs I<sup>2</sup>C support.
|
|-
|-
|Touchscreen
|Touchscreen
| rowspan = 2 |Zinitix BT541
| rowspan = 2 |Zinitix BT541
| N
| Y
| Driver needs some work. Mode 1 support might be required.
| Using bit-banged I<sup>2</sup>C for now. Hardware I<sup>2</sup>C driver needs more work.
|-  
|-  
|Touchkeys
|Touchkeys

Revision as of 17:40, 2 October 2022

Samsung Galaxy Grand Prime+
Grand Prime+ running stock Android
Grand Prime+ running stock Android
Manufacturer Samsung
Name Galaxy Grand Prime+
Codename samsung-grandpplte
Released 2016
Hardware
Chipset MediaTek MT6737T
CPU 4x 1.44 GHz Cortex-A53
GPU Mali-T720 MP2
Display 540x960 LCD
Storage 8 GB
Memory 1.5 GB
Architecture aarch64
Software
Original software Android 6.0.1
postmarketOS
Category testing
Pre-built images no
Mainline yes
Features
Flashing
Works
USB Networking
Works
Internal storage
No data
SD card
No data
Battery
Broken
Screen
Partial
Touchscreen
Broken
Multimedia
3D Acceleration
Broken
Audio
Broken
Camera
Broken
Camera Flash
No data
Connectivity
WiFi
Broken
Bluetooth
Broken
GPS
Broken
Modem
Calls
Broken
SMS
Broken
Mobile data
Broken
Miscellaneous
FDE
Broken
USB OTG
Broken
HDMI/DP
No data
Sensors
Accelerometer
Broken
Proximity
Broken
Haptics
No data
Barometer
No data


Note Note: This page is about Samsung Galaxy Grand Prime Plus, also known as Galaxy J2 Prime based on MediaTek MT6737T.

For Qualcomm MSM8916 variants, see Galaxy Grand Prime.

For Marvell PXA1908 variants, see Galaxy Grand Prime Value Edition

Contributors

  • Tooniis

Users owning this device


How to enter flash mode

While turned off, hold Power+Home+Volume Down, then a menu will appear. Press Volume Up to proceed to flash mode.

UART

Accessing UART is possible through the microUSB port by putting a 619kΩ resistor between the ID pin and ground. Read Serial debugging for more on that. Baud rate is 115200.

Status

Feature Components Status
USB Inventra MUSB

MediaTek T-PHY

P Limited to peripheral mode. PHY driver needs some work to enable host mode.
eMMC MediaTek MSDC

Samsung KMQN10006B-B318

P Limited to HS200 mode. HS400 causes some tuning issues. MSDC driver needs more work.
microSD Slot MediaTek MSDC N Card doesn't respond to commands. Possible power issue.
Display TBD P Using framebuffer configured by stock bootloader for now. Proper display support will require a panel driver and enabling the SoC display system.
GPU ARM Mali-T720 N Needs proper display support. Has a kernel driver and is supported in Mesa so theoretically shouldn't be difficult to bring up.
WiFi TBD N
Bluetooth N
Modem TBD N
GNSS TBD N
Audio Codec MediaTek MT6328 PMIC N
Video Codec TBD N
Battery TBD N
Rear Camera TBD N
Front Camera TBD N
Accelerometer Bosch BMA254 N
Proximity Sensor Sharp GP2AP070S00F N
Touchscreen Zinitix BT541 Y Using bit-banged I2C for now. Hardware I2C driver needs more work.
Touchkeys N
Buttons GPIO controller

MediaTek MT6328

P PMIC keys (power, volume down) work. GPIO keys need device tree description.
Haptics MediaTek MT6328

ERM

N Simple regulator-driven motor. Needs device tree description.
LEDs TBD N

See also