Samsung Galaxy Grand Prime Plus (samsung-grandpplte): Difference between revisions
Appearance
→Status: Add more hardware info |
Fill remaining status fields |
||
Line 38: | Line 38: | ||
| status_proximity = N | | status_proximity = N | ||
| status_hall = - | | status_hall = - | ||
| status_barometer = - | |||
| status_powersensor = - | |||
| status_keyboard = - | |||
| status_touchpad = - | |||
| status_usba = - | |||
| status_hdmidp = - | |||
| status_irtx = - | | status_irtx = - | ||
| status_trustzone = N | | status_trustzone = N | ||
| status_fossbootloader = P | |||
| status = Mainlining in progress. Boots to initramfs with mainline kernel, with working serial console and framebuffer. SoC still needs a lot of work. | | status = Mainlining in progress. Boots to initramfs with mainline kernel, with working serial console and framebuffer. SoC still needs a lot of work. | ||
| booting = yes | | booting = yes |
Revision as of 08:27, 28 October 2022
![]() Grand Prime+ running stock Android | |
Manufacturer | Samsung |
---|---|
Name | Galaxy Grand Prime+ |
Codename | samsung-grandpplte |
Released | 2016 |
Hardware | |
Chipset | MediaTek MT6737T |
CPU | 4x 1.44 GHz Cortex-A53 |
GPU | Mali-T720 MP2 |
Display | 540x960 LCD |
Storage | 8 GB |
Memory | 1.5 GB |
Architecture | aarch64 |
Software | |
Original software | Android 6.0.1 |
FOSS bootloader | partial |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | yes |
Flashing |
Works |
---|---|
USB Networking |
Works |
Internal storage |
No data |
SD card |
No data |
Battery |
Broken |
Screen |
Partial |
Touchscreen |
Works |
Multimedia | |
3D Acceleration |
Broken |
Audio |
Broken |
Camera |
Broken |
Camera Flash |
No data |
Connectivity | |
WiFi |
Broken |
Bluetooth |
Broken |
GPS |
Broken |
Modem | |
Calls |
Broken |
SMS |
Broken |
Mobile data |
Broken |
Miscellaneous | |
FDE |
Broken |
USB OTG |
Broken |
Sensors | |
Accelerometer |
Broken |
Proximity |
Broken |
Haptics |
No data |
Note: This page is about Samsung Galaxy Grand Prime Plus, also known as Galaxy J2 Prime based on MediaTek MT6737T. For Qualcomm MSM8916 variants, see Galaxy Grand Prime. |
Contributors
- Tooniis
Users owning this device
- Tooniis (Notes: SM-G532F)
How to enter flash mode
While turned off, hold Power+Home+Volume Down, then a menu will appear. Press Volume Up to proceed to flash mode.
UART
Accessing UART is possible through the microUSB port by putting a 619kΩ resistor between the ID pin and ground. Read Serial debugging for more on that. Baud rate is 115200.
Status
Feature | Components | Status | |
---|---|---|---|
USB | Inventra MUSB
MediaTek T-PHY |
P | Limited to peripheral mode. PHY driver needs some work to enable host mode. |
eMMC | MediaTek MSDC
Samsung KMQN10006B-B318 |
P | Limited to HS200 mode. HS400 causes some tuning issues. MSDC driver needs more work. |
microSD Slot | MediaTek MSDC | N | Card doesn't respond to commands. Possible power issue. |
Display | BOE S6D78A0
MediaTek DISPSYS |
P | Using framebuffer configured by stock bootloader for now. Proper display support will require a panel driver and enabling the SoC display system. |
GPU | ARM Mali-T720 | N | Needs proper display support. Has a kernel driver and is supported in Mesa so theoretically shouldn't be difficult to bring up. |
WiFi | MediaTek CONSYS | N | |
Bluetooth | N | ||
GNSS | N | ||
Modem | TBD | N | |
Audio Codec | MediaTek MT6328 | N | |
Video Codec | MediaTek VENCSYS
MediaTek VDECSYS |
N | |
Battery | Samsung 1ICP6/57/61
Samsung S2MU005 |
N | |
Rear Camera | TBD
MediaTek CAMSYS |
N | |
Front Camera | TBD
MediaTek CAMSYS |
N | |
Accelerometer | Bosch BMA254 | N | |
Proximity Sensor | Sharp GP2AP070S00F | N | |
Touchscreen | Zinitix BT541 | Y | Using bit-banged I2C for now. Hardware I2C driver needs more work. |
Touchkeys | N | ||
Buttons | GPIO controller
MediaTek MT6328 |
P | PMIC keys (power, volume down) work. GPIO keys need device tree description. |
Haptics | MediaTek MT6328
ERM |
N | Simple regulator-driven motor. Needs device tree description. |
LEDs | TBD | N |