Jump to content

Xiaomi Redmi Note 5A: Difference between revisions

From postmarketOS Wiki
Flafflar (talk | contribs)
Add instructions for entering EDL mode
Flafflar (talk | contribs)
m Tested that the battery is working
Line 23: Line 23:
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? -->
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? -->
| status_mainline = <!-- Instead of a Linux kernel fork, it is possible to run mainline. -->
| status_mainline = <!-- Instead of a Linux kernel fork, it is possible to run mainline. -->
| status_battery = <!-- Charging the battery with charging-sdl is possible -->
| status_battery = Y
| status_3d = <!-- Hardware accelerated 3D graphics (e.g. with freedreno) -->
| status_3d = <!-- Hardware accelerated 3D graphics (e.g. with freedreno) -->
| status_audio = <!-- Using the device's speakers/headphone jack works -->
| status_audio = <!-- Using the device's speakers/headphone jack works -->

Revision as of 11:21, 28 May 2023

Xiaomi Redmi Note 5A
Xiaomi Redmi Note 5A running XFCE4
Xiaomi Redmi Note 5A running XFCE4
Manufacturer Xiaomi
Name Redmi Note 5A
Codename xiaomi-ugg
Released 2017
Hardware
Chipset Qualcomm Snapdragon 435 (MSM8940)
CPU 1.4 GHz Cortex-A53
GPU Adreno 505
Display 720x1280 IPS LCD
Storage 32G
Memory 3GB
Architecture aarch64
Software
Original software Android 7.1.2, MIUI 11
FOSS bootloader no
postmarketOS
Category testing
Pre-built images no
Features
Flashing
Works
USB Networking
Works
Internal storage
No data
SD card
No data
Battery
Works
Screen
Partial
Touchscreen
Works
Multimedia
3D Acceleration
No data
Audio
No data
Camera
No data
Camera Flash
No data
IR TX
No data
Connectivity
WiFi
No data
Bluetooth
No data
GPS
No data
Modem
Calls
No data
SMS
No data
Mobile data
No data
Miscellaneous
FDE
No data
USB OTG
No data
Sensors
Accelerometer
No data
Magnetometer
No data
Ambient Light
No data
Proximity
No data
Hall Effect
No data
Haptics
No data
Barometer
No data
Power Sensor
No data


Contributors

  • Flafflar

Users owning this device

  • Bczeman
  • Filip2cz (Notes: Prime version - this just added fingerprint reader, better camera and littlebit better cpu)
  • Flafflar (Notes: Broken camera)
  • Xiaoyu2006 (Notes: Broken display)


How to enter flash mode

While the phone is off, hold the Power and Volume Down buttons together for a few seconds.

How to enter EDL mode

EDL mode (Emergency Download Mode) is a special mode in Qualcomm devices that allows, among other things, flashing firmware even when the phone is completely bricked. This might come useful in case something goes extremely wrong and the device won't even boot to fastboot.

To boot into EDL, you must first disassemble the device in order to expose the motherboard points required. This phone is very easy to disassemble, you can search for videos on YouTube if necessary. Once you have removed the back case and disconnected the battery, find the points shown below on the motherboard:

EDL testpoints on Redmi Note 5A motherboard (highlighted in red)

These are the test points that enable EDL mode. With the battery disconnected, use a metal tweezer or a small wire to short these two points. While keeping them sorted, plug the phone to a computer. The device should show up as "Qualcomm HS-USB QDLoader 9008". You can now use this tool to download firmware to your device.

Installation

See also