Nothing Phone 1 (nothing-spacewar)
Appearance
This device has been tested with postmarketOS, but its device package has not yet been added to the postmarketOS repositories.
This means that it cannot be selected in pmbootstrap.
This means that it cannot be selected in pmbootstrap.
![]() Nothing Phone 1 | |
Manufacturer | Nothing |
---|---|
Name | Phone 1 |
Codename | nothing-spacewar |
Released | 2022 |
Type | handset |
Hardware | |
Chipset | Qualcomm Snapdragon 778G+ (SM7325-AE) |
CPU | Octa-core (1x2.5 GHz Cortex-A78 & 3x2.4 GHz Cortex-A78 & 4x1.9 GHz Cortex-A55) |
GPU | Adreno 642L |
Display | 2400 x 1080 (120Hz 6.55" AMOLED) |
Storage | 128/256 GB |
Memory | 8/12 GB |
Architecture | aarch64 |
Software | |
Original software | Android |
Original version | 12 |
Extended version | 15 |
FOSS bootloader | partial |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | yes |
Flashing |
Works |
---|---|
USB Networking |
Works |
Internal storage |
Works |
Battery |
Works |
Screen |
Works |
Touchscreen |
Works |
Multimedia | |
3D Acceleration |
Works |
Audio |
Partial |
Camera |
Partial |
Camera Flash |
Works |
Connectivity | |
WiFi |
Works |
Bluetooth |
Works |
GPS |
Broken |
NFC |
Works |
Modem | |
Calls |
Works |
SMS |
Works |
Mobile data |
Works |
Miscellaneous | |
FDE |
Works |
USB OTG |
Works |
Sensors | |
Accelerometer |
Works |
Magnetometer |
Works |
Ambient Light |
Works |
Proximity |
Works |
Haptics |
Broken |
Secondary Bootloader |
Works |
---|---|
Mainline |
Partial |
Internal Storage |
Broken |
USB Host |
Broken |
USB Peripheral |
Partial |
Display |
Works |
Buttons |
Partial |
This device is based on the Snapdragon 778G+. See the SoC page for common tips, guides and troubleshooting steps |
Users owning this device
- Deviled (Notes: 256/8, now "bricked" (WiFi subsystem issues causing CRASDUMP MODE and BT is completely dead))
- JIaxyga
- Keith. (Notes: daily driver, 256GB in black)
- Logg
- Shubhamvis98 (Notes: Dual-booted with Debian Phosh)
- Taxmanindustries (Notes: Calls and texts are FUBAR on pmos :()
Contributors
How to enter flash mode
- Bootloader: Power on the device with both and buttons.
- Recovery: Power on the device with both and buttons.
- Fastbootd: Reboot into bootloader mode first and then run
fastboot reboot fastboot
from a computer.
How to unlock bootloader
Unlocking the bootloader is similar to Google Pixel, use the official guide from Google.
Installation
Note: The device has not yet been merged into pmaports. Use manual installation. |
PostmarketOS Installation guide.
Status
Component | Model | Notes |
---|---|---|
Screen | visionox,rm692e5 | 60/90/120Hz are supported |
Battery | qcom,pm8350bh | Managed by ADSP-remoteproc via GLink battmgr Requires signed ADSP firmware |
southchip,sc8551a | ||
Internal storage |
jedec,ufs-2.0 qcom,sc7280-qmp-ufs-phy qcom,inline-crypto-engine |
KMJIA001RM |
Touchscreen | focaltech,ft3680 @ 0x0 | Connected via spi13, ported from downstream Requires vendor firmware |
GPU | qcom,adreno-635 | Requires a660 (unsigned) & a660-zap (signed) firmware |
SBA-MUX | fcs,fsa4480 @ 0x42 | Connected via i2c1 |
Flash LED | qcom,spmi-flash-led | Connected via pm8350c spmi |
Glyph LED | awinic,aw21018 @ 0x20 | Connected via i2c1 |
WiFi | qcom,wcn6750 | Requires ath11k (unsigned) firmware |
Bluetooth | Requires qca (unsigned) firmware | |
NFC | nxp,55701 @ 0x28 | Connected via i2c9 |
Modem | qcom,sc7280-mpss-pas qcom,sc7280-wpss-pas qcom,sc7280-ipa |
Managed by MPSS-remoteproc Requires signed MPSS & WPSS & IPA firmware |
USB OTG | usb-c-connector | Switches by ADSP-remoteproc via GLink Requires signed ADSP firmware |
Sensors | hexagonrpcd libSSC |
Managed by ADSP-remoteproc Requires signed ADSP firmware |
Haptics | qcom,pmi632-vib | Custom modes required (see downstream dts) |
Type | Sensor | EEPROM | Actuator | Bus |
---|---|---|---|---|
Wide C-Phy | sony,imx766 @ 0x10 | giantec,gt24p128e @ 0x50 | asahi-kasei,ak7377 @ 0xc | cci1_i2c1 |
Ultra Wide D-Phy | samsung,s5kjn1 @ 0x2d | giantec,gt24p128e @ 0x51 | dongwoon,dw9800w @ 0xc | cci1_i2c0 |
Front D-Phy | sony,imx471 @ 0x1a | puya,p24c64f @ 0x52 | - | cci0_i2c0 |
Note:
- EEPROMs work, but sensor drivers can't work with EEPROMs yet. Libcamera doesn't support it either?
- Wide camera doesn't work because C-PHY is not supported by "close-to-mainline" kernel.
Codec | Appointments | Bus | Notes |
---|---|---|---|
nxp,tfa9873 | EAR Speaker | i2c2 @ 0x34 | Rewritten, but still not a version for upstream |
Main Speaker | i2c2 @ 0x35 | ||
qcom,wcd9385-codec | Chassis microphones x3 | ||
Analog I/O audio port |
Known issues
* Glink doesn't switch the usb to the peripheral mode
By default, device tree defines otg mode. During system boot, usb automatically switches to peripheral mode. However, this doesn't happen when the system is already booted. Switching to otg mode works as expected.
Fsa-switcher also works, but switching to peripheral mode may "stick". To exit this mode, hold down the power button and wait until the system reboots 3-5 times. Then the bootloader will switch usb to peripheral mode.
* Both speakers work only in the left channel