BQ Aquaris X / BQ Aquaris X Pro (bq-bardock / bq-bardockpro)

From postmarketOS Wiki
(Redirected from BQ Aquaris X (bq-bardock))
BQ Aquaris X /
Aquaris X Pro
BQ Aquaris X / BQ Aquaris X Pro
BQ Aquaris X / BQ Aquaris X Pro
Manufacturer BQ
Name Aquaris X /
Aquaris X Pro
Codename bq-bardock / bq-bardockpro
Released 2017
Type handset
Hardware
Chipset Qualcomm Snapdragon 626 (MSM8953)
CPU Octa-core 2.2 GHz Cortex-A53
GPU Adreno 506
Display 1080 x 1920 IPS LCD
Storage 32/64 GB
Memory 3/4 GB
Architecture aarch64
Software
Original software Android
Original version 7.1.1
Extended version 8.1
postmarketOS
Category testing
Pre-built images no
Mainline yes
Unixbench Whet/Dhry score 4609.5
This device has been tested with postmarketOS, but its device package has not yet been added to the postmarketOS repositories.
This means that it cannot be selected in pmbootstrap.
Features
Flashing
Works
USB Networking
Works
Internal storage
Works
SD card
Works
Battery
Works
Screen
Works
Touchscreen
Works
Multimedia
3D Acceleration
Works
Audio
Works
Camera
Camera Flash
IR TX
Connectivity
WiFi
Works
Bluetooth
Works
GPS
NFC
Works
Modem
Calls
Works
SMS
Works
Mobile data
Works
Miscellaneous
FDE
Works
USB OTG
Works
Sensors
Accelerometer
Works
Magnetometer
Works
Ambient Light
Works
Proximity
Broken
Haptics
Works
This device is based on the Snapdragon 626.
See the SoC page for common tips, guides and troubleshooting steps

The BQ Aquaris X and BQ Aquaris X Pro are 2017 mid-range devices by Spanish manufacturer BQ. The non-Pro version has a plastic back, while the Pro has a glass back. They otherwise only differ in cameras.

All units of both devices appear to be unfused, meaning that secure boot is disabled and in theory, the first stage bootloader could be replaced and any firmware uploaded to the coprocessors.

Contributors

Users owning this device

  • Adrian (Notes: 3x bardock, 1x bardockpro, both ft8716 and otm1906b)


Unlocking the bootloader

Unlocking the bootloader on these devices is trivial.

  • Enable developer options by pressing "Build number" in the settings repeatingly
  • Insert a SIM card and enable bootloader unlocking in the developer options
  • Reboot to fastboot (conveniently by enabling USB debugging and adb reboot bootloader)
  • Run fastboot oem unlock and confirm with volume buttons
  • When it reboots now, use the volume buttons to select fastboot again
  • Run fastboot flashing unlock_critical and confirm yet again
  • Done! Your bootloader is now fully unlocked and you're ready to flash lk2nd

How to enter flash mode

  • Bootloader: Power on the device with both Power and Volume Down buttons.
  • Recovery: Power on the device with both Power and Volume Up buttons.
  • EDL: Power off the device, hold both Volume Up and Volume Down buttons for 10 seconds, then plug in a USB cable

Installation

Installing lk2nd before postmarketOS is required. Grab a prebuilt from the latest CI run or build it from the repository yourself, unzip it and run fastboot flash boot lk2nd.img in fastboot.

Use pmbootstrap to build your own installation image.

Mainline

There are two panel/touchscreen combinations: ft8716 (with ft8716 touch) and otm1906b (with ili2120 touch). Both touchscreens and panels have mainline drivers and are fully supported.

The buttons under the screen are actually part of the touchscreen and currently not supported.

Microphones are not working due to PipeWire related issues, generally they should work fine once the MSM8953 PipeWire issues are fixed.

UART

UART on these devices uses a baud rate of 115200. UART pins on the bardock board, click for higher resolution

See also