Radxa Zero (radxa-zero): Difference between revisions
m Add type and change originalsoftware https://github.com/radxa/debos-radxa |
m Remove duplicate type and migrate <source> tags to <syntaxhighlight> |
||
Line 15: | Line 15: | ||
| memory = 512MB/1GB/2GB/4GB LPDDR4 | | memory = 512MB/1GB/2GB/4GB LPDDR4 | ||
| architecture = aarch64 | | architecture = aarch64 | ||
| type = | | type = Single Board Computer | ||
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) --> | <!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) --> | ||
| status_usbnet = <!-- USB networking does work? then put Y here and delete this comment --> | | status_usbnet = <!-- USB networking does work? then put Y here and delete this comment --> | ||
Line 42: | Line 42: | ||
| pmoskernel = linux-edge | | pmoskernel = linux-edge | ||
| whet_dhry = 1657.2 | | whet_dhry = 1657.2 | ||
| status_uboot = yes | | status_uboot = yes | ||
| status_uboot_primary = Y | | status_uboot_primary = Y | ||
Line 90: | Line 89: | ||
3. Start the build process and install the completed image to a sdcard | 3. Start the build process and install the completed image to a sdcard | ||
< | <syntaxhighlight lang="shell-session"> | ||
$ pmbootstrap install --sdcard /dev/sdX | $ pmbootstrap install --sdcard /dev/sdX | ||
(replace /dev/sdX with the device for your sdcard or the emmc of it) | (replace /dev/sdX with the device for your sdcard or the emmc of it) | ||
</ | </syntaxhighlight> | ||
4. If you install pm os on sdcard , then Place the sdcard into the Radxa Zero and boot it. If not unplug the usb cable. | 4. If you install pm os on sdcard , then Place the sdcard into the Radxa Zero and boot it. If not unplug the usb cable. | ||
Latest revision as of 16:22, 26 October 2023
![]() Diy dock + Radxa Zero + External Display | |
Manufacturer | Radxa |
---|---|
Name | Zero |
Codename | radxa-zero |
Released | 2021 |
Type | single board computer |
Hardware | |
Chipset | Amlogic S905Y2 |
CPU | Quad Cortex-A53 1.8 GHz |
GPU | Mali G31 MP2 |
Display | MicroHDMI 2.1 - 4K@60 |
Storage | None/8/16/32/64/128GB EMMC + SDCard |
Memory | 512MB/1GB/2GB/4GB LPDDR4 |
Architecture | aarch64 |
Software | |
Original software | Debian |
Original version | 10 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | yes |
postmarketOS kernel | linux-edge |
Unixbench Whet/Dhry score | 1657.2 |
Flashing |
No data |
---|---|
USB Networking |
No data |
Internal storage |
No data |
SD card |
No data |
Screen |
Works |
Multimedia | |
3D Acceleration |
Works |
Audio |
Broken |
Camera Flash |
No data |
Connectivity | |
WiFi |
Partial |
Bluetooth |
Works |
Miscellaneous | |
FDE |
Partial |
USB OTG |
Works |
HDMI/DP |
No data |
Sensors | |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Primary Bootloader |
Works |
---|---|
Mainline |
Works |
Internal Storage |
Works |
SD card |
Works |
USB Host |
Works |
USB Peripheral |
Works |
Display |
Works |
Keyboard |
Works |
Buttons |
No data |
Maintainer(s)
Contributors
Users owning this device
How to enter flash mode
The way of boot into flash rom via hidden bootrom hdmi feature might work on this device. (see the see also section of amlogic page) |
hold down usb-boot button on back of pcb
How to use the boot rom
see Amlogic
Expose embedded eMMC as a USB Mass Storage device
Fellow https://wiki.radxa.com/Zero/dev/maskrom#Enable_maskrom
Installation
1. Follow the steps on Installation_guide#Initialization
2. Choose the radxa-zero
device
3. Start the build process and install the completed image to a sdcard
$ pmbootstrap install --sdcard /dev/sdX
(replace /dev/sdX with the device for your sdcard or the emmc of it)
4. If you install pm os on sdcard , then Place the sdcard into the Radxa Zero and boot it. If not unplug the usb cable.
Boot process
If emmc is bootable :
bootrom ==> emmc ==> uboot ==> postmarketOS
Else if sdcard is bootable :
bootrom ==> emmc ==> uboot ==> postmarketOS
Else :
bootrom ==> flashmode
Wifi
Depend on your Radxa Zero, it might be had one of those Wi-Fi modules : AW-CM256SM(some of the Radxa Zero v1.5 had this),AP6256(Radxa Zero 2/4/8GB had this),AP6212(Radxa Zero 1024/512MB had this) so the wifi of your Radxa Zero might not work due to the wifi modules on your Radxa Zero isnt supported by the kernel or the firmware that is in the pm os.
As of now , the only Wi-Fi modules that seem to supported by the kernel and the firmware is AP6256.
See also
- pmaports!2948 Initial merge request (First Attempt)
- pmaports!3865 Initial merge request (Second Attempt)