Sony Xperia Go (sony-lotus): Difference between revisions
Appearance
m Add type |
mNo edit summary |
||
Line 118: | Line 118: | ||
< | <pre> | ||
Line 178: | Line 178: | ||
Uncompressing Linux... done, booting the kernel. | Uncompressing Linux... done, booting the kernel. | ||
</ | </pre> |
Latest revision as of 11:34, 1 February 2025
This device has been tested with postmarketOS, but its device package has not yet been added to the postmarketOS repositories.
This means that it cannot be selected in pmbootstrap.
Status: booting (with downstream kernel) but the screen is not work
This means that it cannot be selected in pmbootstrap.
Status: booting (with downstream kernel) but the screen is not work
Manufacturer | Sony |
---|---|
Name | Xperia Go |
Codename | sony-lotus |
Model | st27i/st27a |
Released | 2012 |
Type | handset |
Hardware | |
Chipset | ST-Ericsson NovaThor U8500 |
CPU | Dual-core 1.0 GHz Cortex-A9 |
GPU | Mali-400 |
Display | 320x480 |
Storage | 8 GB |
Memory | 0.5 GB |
Architecture | armv7 |
Software | |
Original software | Android |
Original version | 2.X |
postmarketOS | |
Category | testing |
Pre-built images | no |
postmarketOS kernel | mainline (WiP) |
Flashing |
No data |
---|---|
USB Networking |
No data |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
No data |
Touchscreen |
No data |
Multimedia | |
3D Acceleration |
No data |
Audio |
Broken |
Camera |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
No data |
Bluetooth |
No data |
GPS |
No data |
NFC |
No data |
Modem | |
Calls |
No data |
SMS |
No data |
Mobile data |
No data |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
Users owning this device
- Worldbluesquadron (Notes: Running LineageOS 12.1)
Mainline kernel
List of features working on mainline kernel:
Component | Model | Status | Notes |
---|---|---|---|
SoC | U8500 | Y | |
USB | - | Y | Working |
eMMC | M8G2FB | Y | |
microSD | - | Y | |
Display | Hitachi DSI R61529/SEIKO RJ248 | N | |
Light Controller | as3677 | N | Responsible for lcd backlight , physical navigation backlight , Ambient Light (red/green/blue) |
Touchscreen | AB8500 | Y | |
Charging IC | ??? | Y | |
Buttons | - | Y | GPIO |
GPU | Y | ||
WLAN | CW1200 | Y | Not Sure the firmware from linux-firmware will work on it or not |
Bluetooth/GPS | CG2900 | N | there are a staging driver that seem to stuck at mail list https://lwn.net/Articles/435847/ |
Modem | - | N | known to be broken |
Front camera | ??? | N | |
Main camera | ??? | N | |
Magnetometer | LSM303DLH | Y | |
Accelerometer | LSM303DLHC | Y |
UART
colour | pin | |
---|---|---|
Red | Rx | |
White | Tx | |
Black | GND |
Boot Log
S1 Boot U8500 1240-4128 CRH1099189_R10E013 2012-05-12 10:06 (RioGrande (DB8500) chipset) SoC settings: INFO: @(#)SOC-SETTINGS v4.0.1-(F)-batt-volt db8500 v2 1000Mhz Oct 31 2012 12:04:18 SoC settings: INFO: Vbat check 0x00000270 SoC settings: INFO: No memory mounted on CS1 SoC settings: INFO: Vendor ID = 0x00000001, CS0 density = 0x00000018, CS1 density = 0x00000000 SoC settings: INFO: CS0 revision ID1 = 0x00000001, CS0 revision ID2 = 0x00000000 SoC settings: INFO: AVS Enable, FVR21 value = : 0x87191749, FVR22 value = : 0x0023de13 SoC settings: INFO: Memory size=0x20000000 (512 MB), CS0 (512 MB) CS1 (0 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Set 1GHz OK ISSW returned from MEMINIT, vendor: Samsung (0x01), density (CS0): 4Gbit (0x18), density (CS1): Unknown! (0x00) MEMINIT passed OK DB CutId:008500B2 AB CutId:33 ISSW version:R1G-EC13 P2D With "0001-ISSW-Clean-caches-on-wd-reset.patch" and mem_issw=1M@160M MEMINIT version:02 PRCMU firmware version:03.3F.05 (for 8500 chipset) Using MEMINIT from platform Using PRCMU firmware from platform AB8500 Turn on status: 0x02 ( PonKey1. ) AB8500 Reset status: 0x05 ( Reset by ResetAB8500n ball. Reset by SwReset4500n bit. ) DB8500 Reset status: 0x0020 ( Power on reset. ) AB8500 Switch Off : 0x01 ( SwOffCmd ) TA ELF address buffer (secure mode): 0x4000700C plf_GetStartupReasonBitfield S1 Boot Startup info: [ONKEY PRESSED] Found i2c controller Found i2c controller MID 0: Samsung MMC 'M8G2FB' 7.288 GB S1 Boot "1240-4128 U8500 CRH1099189_R10E013" (2012-05-12 10:06) Reboot reason: 0x0 (Coldboot) ControlledRooting: Status = [Done] Setup DK: Setup failed with SECMGR error=[1023] ta_status=[4] FlaFla is set S1 BOOT check if any USB connection... s1_main_loop: No Service mode comm interface found! boot_partitions: The following partitions will be booted (in this order): partID:05 partID:03 Vibrate ON Vibrate OFF plf_boot_elf: Starting booting of partID:05 plf_boot_elf (modem boot): Modem version info: NWM_STACK=MB10A_12w22_2_18102 MODEM_DELIVERY=49020908 MODEM_VARIANT=SONY2020 plf_boot_elf (modem boot): Booting started elf_verify: No SIN Header found! elf_verify: Proceeding since SIN verification is not enforced for partition 3 plf_boot_elf: Starting booting of partID:03 ATAG list starts at 0x00000100 Kernel commandline: startup=0x1 warmboot=0x0 ta_info=9,4,256 androidboot.bootloader=s1 androidboot.serialno=CB5A1KNBU5 rootwait logo.nologo androidboot.console=null mpcore_wdt.mpcore_margin=359 board_id=1 androidboot.hardware=st-ericsson mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M mem_modem=16M@112M mem=32M@128M mem_issw=1M@160M hwmem=71M@161M mem=280M@232M semcandroidboot.babe1324=43423541314b4e425535 Vibrate OFF [Last word from S1 BOOT] Jumping to kernel at address [0x00008000], all your base are belong to us! Uncompressing Linux... done, booting the kernel.