Next Thing Co. CHIP (ntc-chip): Difference between revisions
Appearance
Remove command line to rename kernel as it is done automatically |
ntc-chip: Add instructions to change uboot-configuration |
||
Line 78: | Line 78: | ||
* Press enter during boot up to access the U-Boot console | * Press enter during boot up to access the U-Boot console | ||
* On the console type `fastboot 0` | * On the console type `fastboot 0` | ||
== Configure U-Boot == | |||
PostmarketOS loads an initramfs together with the kernel, while original Debian installation only used the kernel. | |||
To boot PostmarketOS we need to change the U-Boot configuration to support the initramfs. | |||
From the U-boot serial console issue the following commands | |||
<syntaxhighlight lang="shell-session"> | |||
> setenv bootcmd "gpio set PB2; ${bootcmd_fel}; ${boot_initrd};" | |||
> saveenv | |||
</syntaxhighlight> | |||
== Create the UBIfs image == | == Create the UBIfs image == |
Revision as of 13:43, 25 March 2020
![]() Next Thing Co. CHIP | |
Manufacturer | Next Thing Co. |
---|---|
Name | CHIP |
Codename | ntc-chip |
Released | 2015 |
Hardware | |
Chipset | Allwinner R8 |
CPU | 1x 1.0 GHz Cortex-A8 |
GPU | Mali-400 MP1 |
Display | Composite video |
Storage | 8GB MLC NAND |
Memory | 512 MB DDR3 |
Architecture | armv7 |
Software | |
Original software | Debian on Linux 4.4 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Flashing |
No data |
---|---|
USB Networking |
No data |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
No data |
Multimedia | |
3D Acceleration |
No data |
Audio |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
No data |
Bluetooth |
No data |
NFC |
No data |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
- Symmetrist
Maintainer(s)
- Symmetrist
Users owning this device
How to enter flash mode
The CHIP has two different flashing modes:
- FEL mode: used to flash bootloader and rootfs
- Fastboot mode: used to flash rootfs
To enter FEL mode:
- Connect the FEL and GND pins with a jumper cable
- Power on the CHIP
To enter Fastboot mode:
- Connect an serial (UART) USB adapter to UART1-TX, UART1-RX and GND
- Power on the CHIP
- Press enter during boot up to access the U-Boot console
- On the console type `fastboot 0`
Configure U-Boot
PostmarketOS loads an initramfs together with the kernel, while original Debian installation only used the kernel.
To boot PostmarketOS we need to change the U-Boot configuration to support the initramfs.
From the U-boot serial console issue the following commands
> setenv bootcmd "gpio set PB2; ${bootcmd_fel}; ${boot_initrd};"
> saveenv
Create the UBIfs image
- Configure the installation
$ pmbootstrap init
- Build the system
$ pmbootstrap install
In `workdir/chroot_rootfs_ntc-chip` there is the rootfs for your ntc-chip The following commands needs to be launched from your pmbootstrap workdir
- Copy dtb from linux-ntc-chip
$ sudo mkdir chroot_rootfs_ntc-chip/boot/dtbs
$ sudo cp cache_git/pmaports/device/testing/linux-ntc-chip/sun5i-r8-chip.dtb chroot_rootfs_ntc-chip/boot/dtbs/
Install mtd-utils from your distro repositories e.g. `pacman -S mtd-utils`
- Create the UBIfs image
$ mkdir ubi
$ sudo mkfs.ubifs -m 16384 -e 0x1f8000 -c 2000 -r chroot_rootfs_ntc-chip ubi/ubifs.img
$ sudo chown youruser:youruser ubi/ubifs.img
$ ubinize -o ubi/ubi.img -m 16384 -p 2MiB -s 16384 cache_git/pmaports/device/testing/device-ntc-chip/ubinize.cfg
$ img2simg ubi/ubi.img ubi/ubi.img.sparse 2097152
Flash the UBIfs image
- Enter fastboot mode as described above
- On your computer
$ sudo fastboot erase UBI
$ sudo fastboot flash UBI ubi/ubi.img.sparse
$ sudo fastboot reboot
See also
- pmaports!1098 Initial merge request
- Sunxi wiki page
- Wikipedia wiki page