BQ Aquaris X5 (bq-paella): Difference between revisions
No edit summary |
m Edited flash section regarding bq-paella, updated status_flashing from P to Y |
||
Line 16: | Line 16: | ||
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) --> | <!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) --> | ||
| status_usbnet = Y | | status_usbnet = Y | ||
| status_flashing = | | status_flashing = Y | ||
| status_touch = P | | status_touch = P | ||
| status_screen = Y | | status_screen = Y | ||
Line 76: | Line 76: | ||
'''bq-paella:''' | '''bq-paella:''' | ||
# Install [https://github.com/msm8916-mainline/lk2nd lk2nd] following the [https://github.com/msm8916-mainline/lk2nd#building Building] section (just needed the first time) | |||
# | # boot to lk2nd and follow the [[Installation_guide]] (tested <code>pmbootstrap flasher ..</code> and <code>fastboot</code> methods) | ||
# follow the [[Installation_guide]] | |||
== Status == | == Status == |
Revision as of 07:19, 29 April 2020
![]() BQ Aquaris X5 Cyanogen Edition running weston on postmarketOS downstream | |
Manufacturer | BQ |
---|---|
Name | Aquaris X5 |
Codename | bq-picmt, bq-paella |
Released | 2015 |
Hardware | |
Chipset | Qualcomm MSM8916T Snapdragon 412 |
CPU | Quad-core 1.4 GHz Cortex-A53 |
GPU | Adreno 306 |
Display | 720 x 1280 (IPS LCD capacitive touchscreen, 16M colors) |
Storage | 16GB / 32GB |
Memory | 2GB / 3GB |
Architecture | armv7 |
Software | |
Original software | Android 7.1.2, CM 13.1 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Flashing |
Works |
---|---|
USB Networking |
Works |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
Works |
Touchscreen |
Partial |
Multimedia | |
3D Acceleration |
No data |
Audio |
No data |
Camera |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
Works |
Bluetooth |
No data |
GPS |
No data |
NFC |
No data |
Modem | |
Calls |
No data |
SMS |
No data |
Mobile data |
No data |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
Maintainer(s)
Users owning this device
- Aleksander (Notes: WWAN stack tinkering)
- DancesWithCycles (Notes: Posh on pmOS with touch not working)
- Delta503 (Notes: testing on edge against being daily driver)
- Jakko
- Lazzardo (Notes: CyanogenMod Edition)
- Linmob (Notes: broken volume button)
- Marissachan (Notes: 32GB/2GB PMOS edge Phosh)
- Minecrell (Notes: BQ version)
- Mxkrsv (Notes: CyanogenMod Edition)
- PanzerSajt
- Pojntfx
- Rapto
- Sulu
- TuxLX
- Voj343
How to enter flash mode
bq-paella:
- Recovery: Power on the device with both
Power
andVolume Down
buttons. - Stock fastboot: Power on the device with both
Power
andVolume Up
buttons. - lk2nd Fastboot: Power on the device. After it vibrates, hold
Volume Down
.
Installation
bq-picmt:
By now the way I flashed the device and having it working was following Installation from recovery mode guide and using the adb sideload method
bq-paella:
- Install lk2nd following the Building section (just needed the first time)
- boot to lk2nd and follow the Installation_guide (tested
pmbootstrap flasher ..
andfastboot
methods)
Status
Currently work is separated based on firmware installed, if you installed the Cyanogen Edition firmware will be referred as bq-paella, if you installed the BQ Android firmware it will be referred as bq-picmt. So here is a summary for both:
bq-picmt: runs on downstream kernel
Works: USB Network, WiFi, Display, weston, weston-calibrator
Buggy: ts_calibrate: to make screen get touches I incrementally have to touch screen with one finger and then with that finger on screen touch the crosshair, then for the second two fingers and crosshair, for the third three fingers and crosshair...don't know why but it started happening when I replaced my broken screen with a new one, if someone has this device with original screen can check if the same issue is present or not
Modem doesn't work, in dmesg I get DATA5_CNTL error relative to no such device
bq-paella: runs on mainline kernel
Works: USB Network, WiFi, Bluetooth
See also
Initial merge request [1]