Sony Xperia Z (sony-yuga): Difference between revisions
Appearance
Added some more clarification |
m Restructure page |
||
Line 14: | Line 14: | ||
| memory = 2 GB | | memory = 2 GB | ||
}} | }} | ||
== Contributors == | |||
* wfranken (porting and testing) | * wfranken (porting and testing) | ||
Line 20: | Line 20: | ||
* ata2001 (help via IRC) | * ata2001 (help via IRC) | ||
* opendata (help via IRC) | * opendata (help via IRC) | ||
== Device knowledge == | |||
=== Special keycombo's === | === Special keycombo's === | ||
Line 42: | Line 44: | ||
This is also the reason why LineageOS boot.img is far larger than postmarketOS boot image (the recovery is inside it). | This is also the reason why LineageOS boot.img is far larger than postmarketOS boot image (the recovery is inside it). | ||
== Current state == | |||
=== What works === | === What works === | ||
Line 70: | Line 74: | ||
* Wifi | * Wifi | ||
=== Installation procedure == | === Mainline support === | ||
* It should be possible to run [[The Mainline Kernel]] on the device. At least there is a <code>dts</code> file already in the 4.14 kernel: <code>arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts</code> | |||
At the moment this is not tested yet. | |||
== Install == | |||
=== Installation procedure === | |||
Follow the [[Installation guide]]. | Follow the [[Installation guide]]. | ||
Line 80: | Line 92: | ||
** If all else fails: buy a new battery | ** If all else fails: buy a new battery | ||
== | == References == | ||
* [https://github.com/LineageOS/android_kernel_sony_msm8974 Kernel Source] | * [https://github.com/LineageOS/android_kernel_sony_msm8974 Kernel Source] |
Revision as of 10:18, 6 July 2018
![]() Sony Xperia Z running Weston | |
Manufacturer | Sony |
---|---|
Name | Xperia Z |
Codename | yuga |
Released | 2013 |
Hardware | |
Chipset | Qualcomm APQ8064 Snapdragon S4 Pro |
CPU | Quad-core 1.5 GHz Krait |
GPU | Adreno 320 |
Display | 1080x1920 TFT |
Storage | 16 GB |
Memory | 2 GB |
Software | |
Original software | Android 4.1.2 on Linux 3.0.31 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | no |
Flashing |
No data |
---|---|
USB Networking |
No data |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
No data |
Touchscreen |
No data |
Multimedia | |
3D Acceleration |
No data |
Audio |
No data |
Camera |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
No data |
Bluetooth |
No data |
GPS |
No data |
NFC |
No data |
Modem | |
Calls |
No data |
SMS |
No data |
Mobile data |
No data |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
- wfranken (porting and testing)
- ollieparanoid (help via IRC)
- ata2001 (help via IRC)
- opendata (help via IRC)
Device knowledge
Special keycombo's
- Boot to bootloader (fastboot): unplug device, hold volume up and plug usb into device
- Reset if stuck: hold volume up and power button till the phone shakes
Notification LED information
- Constant blue LED: fastboot mode
- Slowly blinking red LED when plugged in: battery cannot hold any charge.
- Blinking red LED when trying to boot: Cannot boot, maybe offsets are wrong?
- Constant red LED on while plugged in: charging
Non-standard notes
The Xperia Z does not have a recovery partition, so flashing PostmarketOS erases any recovery you have installed. Instructions across the internet for reinstalling a custom recovery are almost all incorrect.
To install a custom recovery on the Xperia Z:
- put the device in fastboot mode
- run
fastboot flash boot recovery.img
(replacerecovery.img
with the filename of your recovery of choice)
This is also the reason why LineageOS boot.img is far larger than postmarketOS boot image (the recovery is inside it).
Current state
What works
- charging
- network through USB
- telnet in initramfs
- ssh
- adjusting the led, torch and the lcd backlight
- display
- Weston
- Xwayland
- touchscreen
Known issues
- Splash screens don't work
- Launching Weston is delayed by 135 seconds to let udev settle down
- Display works only when running
cat /sys/class/graphics/fb0/modes > /sys/class/graphics/fb0/mode
after being logged in using SSH.
What has not been tested
- Bluetooth
- 3G
- Sound
- Phone calls
- SD card
- Wifi
Mainline support
- It should be possible to run The Mainline Kernel on the device. At least there is a
dts
file already in the 4.14 kernel:arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
At the moment this is not tested yet.
Install
Installation procedure
Follow the Installation guide.
Troubleshooting
- If you get a slowly blinking red LED when trying to charge, this could mean your battery does not get charged. You have then have two options:
- Open the back (eg. with a hairdryer) and try to unplug and plug the battery
- If all else fails: buy a new battery