Samsung Galaxy Mini 2 (samsung-jena): Difference between revisions
mNo edit summary |
m typo |
||
Line 251: | Line 251: | ||
capabilities: ethernet physical | capabilities: ethernet physical | ||
configuration: broadcast=yes multicast=yes | configuration: broadcast=yes multicast=yes | ||
</source | </source> |
Revision as of 19:41, 22 November 2018
WARNING: This device is not recommended for future use with postmarketOS due to its armhf architecture. Alpine Linux (the distribution that postmarketOS extends) pmaports#599 has been considering dropping it. The processor of the device may support the armv7 architecture. If so, you can modify the device package and change the architecture accordingly. |
![]() Samsung s6500d | |
Manufacturer | Samsung |
---|---|
Name | Galaxy Mini 2 |
Codename | samsung-s6500d, s6500, jena |
Released | 2012 |
Hardware | |
Chipset | Qualcomm MSM7227A Snapdragon S1 |
CPU | ARM Cortex-A5 800 Mhz |
GPU | Adreno 200 |
Display | 320×480 |
Storage | 4GB |
Memory | physically probably 512MiB, limited by kernel to ~385MiB (faulty dices/Java something?) |
Architecture | armhf |
Software | |
Original software | Android 2.3.4 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | no |
postmarketOS kernel | 3.4 from Cyanogen |
Flashing |
Works |
---|---|
USB Networking |
Works |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
Works |
Touchscreen |
Partial |
Multimedia | |
3D Acceleration |
No data |
Audio |
No data |
Camera |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
No data |
Bluetooth |
No data |
GPS |
No data |
NFC |
No data |
Modem | |
Calls |
No data |
SMS |
No data |
Mobile data |
No data |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
Maintainer(s)
- also Halamix2
What works
- Boots
- SSH through USB
- display
- flashing
What does not work
- Restart after ~2 minutes 22 seconds
- No input (keys and screen)
- osk-keyboard
- Wi-Fi
- XWayland
- FDE
- Not mainlined
- No charging with turned off phone (is it even supported?)
- 3D acceleration
- Accelerometers and other sensors
- Audio
- Bluetooth
- Camera
- GPS
- Mobile data
- SMS
- Voice
To do
informations below may be chaotic and change often |
SMSM_RESET
Most annoying problem sunce everything on the phone has to be done within 2 minutes. After about 2mins 22secs phone reboots with dmesg showing SMSM: Modem SMSM state changed to SMSM_RESET This message is hardcoded into arch/arm/mach-msm/smd.c
Probably caused my modem, check all MODEM and MSM*_MODEM_* related options in menuconfig (there is one called reset, one reboot and one just modem) or find binary blobs if possible.
Touch screen
The screen as well as two touch buttons (menu and back) are combined together as /dev/input/event1. It displays some sort of animation when pressing buttons in postmarket demos window in weston but only for first press or two. weston-calibrate does not work
Home button and volume buttons are /dev/input/event1, where power button is recognised as /dev/input/event6
Mainline
Currently we have working 2.6 kernel, no DTS files for qcom-msm7227a.
Get data form all over the kernel source code (mainly arch/mach-msm/board-<board name>.c for starters and recreate it in .dts file(s).
Get UART working, then test basic DTS with just basics to get earlycon/earlyprintk working:
- used voltage is 1.8V
- needed resistor is *probably* 619kΩ
- unknown name of the port in original kernel, candidates are ttyMSM0, tty0, ttyHS0, ttyHSL0 and ttyGS0
- trying to get UART on 0xa9a00000 (ttyMSM0)
- dtb probably misses clocks, maybe interrupts and other things
This dtb file goal is to get working UART, nothing more, rest of the work will be continued on regular git repository when/if UART starts working |
Useful links (mainly dts stuff)
The Mainline Kernel – our docs about mainlining
Qualcomm mainline porting — our sparse docs about Qualcomm mainlining
Qualcomm SOC Mainlining Project – sadly no MSM7227a
Documentation/devicetree/ inside linux kernel files, should contain newest documentation about dts files, should be most reliable source of information
How to enter flash mode
Press power button and hold home button and VOL-, then press VOL+ to continue
Alternatively, plug in microUSB plug with GND and ID pins connected through 300KΩ resistor. (so-called USB jig)
Installation
For now see Installation Guide and Flashing on Porting to a new device
Partitions
fdisk -l /dev/mmcblk0
omitting empty partition (25)
Disk /dev/mmcblk0: 3.7 GiB, 3909091328 bytes, 7634944 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 1 40 40 20K 4d QNX4.x CFG_DATA
/dev/mmcblk0p2 41 340 300 150K 45 unknown QCSBL
/dev/mmcblk0p3 341 41300 40960 20M c W95 FAT32 (LBA) FAT
/dev/mmcblk0p4 41301 7634943 7593643 3.6G 5 Extended ? / partition.bin
/dev/mmcblk0p5 49152 51151 2000 1000K 46 unknown OEMSBL
/dev/mmcblk0p6 51152 53151 2000 1000K 47 unknown APPSBL
/dev/mmcblk0p7 53152 57151 4000 2M 5d unknown SSD
/dev/mmcblk0p8 57152 81727 24576 12M 48 unknown APPS / boot partition
/dev/mmcblk0p9 81728 87871 6144 3M 4a unknown MODEM_ST1
/dev/mmcblk0p10 87872 94015 6144 3M 4b unknown MODEM_ST2
/dev/mmcblk0p11 94016 110399 16384 8M 90 unknown PERSIST
/dev/mmcblk0p12 110400 134975 24576 12M 91 unknown RECOVERY
/dev/mmcblk0p13 134976 143167 8192 4M 92 unknown PARAMETER
/dev/mmcblk0p14 143168 151359 8192 4M 93 Amoeba SECURE
/dev/mmcblk0p15 151360 152383 1024 512K 95 unknown PIT
/dev/mmcblk0p16 152384 1176383 1024000 500M 82 Linux swap / Solaris SYSTEM
/dev/mmcblk0p17 1176384 1483583 307200 150M 94 Amoeba BBT CACHE
/dev/mmcblk0p18 1483584 3396415 1912832 934M 83 Linux USERDATA
/dev/mmcblk0p19 3396416 3420991 24576 12M 65 Novell Netware 386 EFS
/dev/mmcblk0p20 3420992 3470143 49152 24M 9a unknown IMG_BACKUP
/dev/mmcblk0p21 3470144 3478335 8192 4M 63 GNU HURD or SysV MISC
/dev/mmcblk0p22 3478336 3580735 102400 50M 67 unknown HIDDEN
/dev/mmcblk0p23 3580736 7429803 3849068 1.9G 64 Novell Netware 286 UMS
/dev/mmcblk0p24 7429804 7437995 8192 4M 58 unknown MODEM_BKP
Downstream kernel
Basic info
samsung-s6500d:~$ neofetch
user@samsung-s6500d
-------------------
OS: postmarketOS 1.0.3 armv7l
Kernel: 3.4.105-caf-kk_2.7-stable
Uptime: 2 mins
Packages: 245 (apk)
Shell: ash
WM: catwm
Terminal: /dev/pts/0
CPU: QCT MSM7x27a FFA (1) @ 1.008GHz
Memory: 45MiB / 385MiB
samsung-s6500d:~$ sudo lshw
samsung-s6500d
description: Computer
width: 256 bits
*-core
description: Motherboard
physical id: 0
*-memory
description: System memory
physical id: 0
size: 385MiB
*-cpu
physical id: 1
bus info: cpu@0
size: 1008MHz
capacity: 1008MHz
capabilities: swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4 cpufreq
*-network:0 DISABLED
description: Ethernet interface
physical id: 1
logical name: rmnet6
serial: 52:b2:c7:40:d1:2d
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:1 DISABLED
description: Ethernet interface
physical id: 2
logical name: rmnet1
serial: de:a7:d7:27:66:c7
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:2
description: Ethernet interface
physical id: 3
logical name: usb0
serial: 6e:78:d2:86:86:26
capabilities: ethernet physical
configuration: broadcast=yes driver=g_ether driverversion=29-May-2008 firmware=msm72k_udc ip=172.16.42.1 link=yes multicast=yes
*-network:3 DISABLED
description: Ethernet interface
physical id: 4
logical name: rmnet5
serial: 32:a3:3f:56:62:1c
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:4 DISABLED
description: Ethernet interface
physical id: 5
logical name: rmnet0
serial: 06:d7:c2:e5:15:85
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:5 DISABLED
description: Ethernet interface
physical id: 6
logical name: rmnet4
serial: da:df:9e:86:b7:9f
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:6 DISABLED
description: Ethernet interface
physical id: 7
logical name: rmnet3
serial: 3e:25:2a:c7:0f:76
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:7 DISABLED
description: Ethernet interface
physical id: 8
logical name: rmnet7
serial: 86:bc:19:51:a1:dd
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes
*-network:8 DISABLED
description: Ethernet interface
physical id: 9
logical name: rmnet2
serial: 9a:d9:81:bb:8e:9e
capabilities: ethernet physical
configuration: broadcast=yes multicast=yes