Samsung Galaxy Note II LTE (samsung-t0lte)
![]() Galaxy Note II | |
Manufacturer | Samsung |
---|---|
Name | Galaxy Note II LTE |
Codename | samsung-t0lte |
Released | 2012 |
Hardware | |
Chipset | Exynos 4412 Quad |
CPU | Quad-core 1.6 GHz Cortex-A9 |
GPU | Mali-400 MP4 |
Display | 720x1280 AMOLED |
Storage | 16/32/64 GB |
Memory | 2 GB |
Architecture | armv7 |
Software | |
Original software | Android 4.1.1 on Linux 3.0.31 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | yes |
postmarketOS kernel | 5.15 |
Flashing |
Partial |
---|---|
USB Networking |
Works |
Internal storage |
No data |
SD card |
No data |
Battery |
Works |
Screen |
Works |
Touchscreen |
Works |
Multimedia | |
3D Acceleration |
Works |
Audio |
Partial |
Camera |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
No data |
Bluetooth |
No data |
GPS |
No data |
NFC |
No data |
Modem | |
Calls |
No data |
SMS |
No data |
Mobile data |
No data |
Miscellaneous | |
FDE |
Works |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
- Jack_Kekzoz
Users owning this device
- BlackEyedSquid (Notes: Verizon model (t0ltevzw), locked bootloader (KitKat update))
- Jack Kekzoz
How to enter flash mode
When the phone is powered off, press and hold down the Home, Vol Down and Power buttons to turn it on in Download mode.
If you have installed a custom recovery, then when the phone is powered off, press and hold down the Home, Vol Up and Power buttons to turn it on in Recovery mode.
Installation
You can install postmarketOS either by flashing the rootfs to an sdcard, and then flashing the kernel using Heimdall when the phone is in Download mode, or you can install it via a recovery zip. It is not possible currently to flash rootfs in Download mode, as Heimdall has issues with flashing rootfs currently (see Heimdall). Please note that for the recovery installation, if you enable FDE, you need to ensure your custom recovery supports the cipher you are using.
Display
There is an issue with the display in that the brightness is too high when it turns on. Simply turning down the brightness, even a little, makes it jump to the correct setting.
FDE
FDE works, but for some reason, not with hardware acceleration.
Audio
pmaports!2913 This merge request adds speaker and mic functionality (not headphone, as the kernel driver needs work to support that. In its current state the headphone audio is very crackly).
Hardware
Part | Name | Mainline kernel support | Notes |
---|---|---|---|
GPU | Mali-400 MP4 | Y | Driver |
Panel | Samsung S6EVR02 LCD panel | N | But there is a patch in pmaports |
Touchscreen | MMS152 | Y | Driver |
WiFi | BCM4334 | Y | brcmfmac driver. WiFi functionality will be tested and added soon. |
Bluetooth | BCM4334 | Y | Driver |
GPS | MDM9615 | ||
Modem | MDM9615 | P | DTSI. This modem is also found in samsung-m3 (GT-i9305). |
Fuel gauge | MAX17047 | Y | Driver |
MFD | MAX77686 | Y | Driver |
Audio codec | WM1811 | Y | Driver. This driver is thought to be an upstreamed version of samsung-m0's downstream driver. t0 driver needs upstreaming for full audio functionality. |
Front Camera | S5K6A3 | Y | Image sensor driver, Imaging subsystem driver. For some reason cameras don't work yet - needs investigating |
Back Camera | S5C73M3 | Y | Driver, SPI driver. For some reason cameras don't work yet - needs investigating |
Flash LED & Vibrator (MFD) | MAX77693 | Y | Driver |
Notification LED | AN30259A | ||
Accelerometer/Gyroscope | LSM330DLC | ||
Touchkey | Cypress ??? | Y | Driver |
Magnetometer | AK8963C | ||
Proximity/Light sensor | CM36651 | ||
MHL | SII9244BO |
Partitions
Output of sudo parted /dev/mmcblk2 print
:
Model: MMC MAG4FB (sd/mmc) Disk /dev/mmcblk2: 15.8GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags:
Number | Start | End | Size | File system | Name | Flags |
---|---|---|---|---|---|---|
1 | 4194kB | 8389kB | 4194kB | BOTA0 | msftdata | |
2 | 8389kB | 12.6MB | 4194kB | BOTA1 | msftdata | |
3 | 12.6MB | 33.6MB | 21.0MB | ext4 | EFS | msftdata |
4 | 33.6MB | 37.7MB | 4194kB | m9kefs1 | msftdata | |
5 | 37.7MB | 41.9MB | 4194kB | m9kefs2 | msftdata | |
6 | 41.9MB | 46.1MB | 4194kB | m9kefs3 | msftdata | |
7 | 46.1MB | 54.5MB | 8389kB | PARAM | msftdata | |
8 | 54.5MB | 62.9MB | 8389kB | BOOT | msftdata | |
9 | 62.9MB | 71.3MB | 8389kB | RECOVERY | msftdata | |
10 | 71.3MB | 164MB | 92.3MB | fat16 | RADIO | msftdata |
11 | 164MB | 432MB | 268MB | ext4 | TOMBSTONES | msftdata |
12 | 432MB | 1866MB | 1434MB | ext4 | CACHE | msftdata |
13 | 1866MB | 4014MB | 2147MB | ext4 | SYSTEM | msftdata |
14 | 4014MB | 4601MB | 587MB | ext4 | HIDDEN | msftdata |
15 | 4601MB | 4610MB | 8389kB | OTA | msftdata | |
16 | 4610MB | 15.8GB | 11.1GB | ext4 | USERDATA | msftdata |
See also
- pmaports!2759 Initial merge request
- Device package
- Kernel package