Huawei Ascend G330 (huawei-u8825): Difference between revisions
Appearance
it boots now |
No edit summary |
||
Line 15: | Line 15: | ||
| architecture = armv7 | | architecture = armv7 | ||
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) --> | <!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) --> | ||
| status_usbnet = <!-- USB networking does work? then put Y here and delete this comment --> | | status_usbnet = Y <!-- USB networking does work? then put Y here and delete this comment --> | ||
| status_flashing = <!-- Flashing with "pmbootstrap flasher" works? Put Y here. It works the same for everything coming below. --> | | status_flashing = P<!-- Flashing with "pmbootstrap flasher" works? Put Y here. It works the same for everything coming below. --> | ||
| status_touch = <!-- Touch screen is working? You can also answer these questions with P for partially. --> | | status_touch = N <!-- Touch screen is working? You can also answer these questions with P for partially. --> | ||
| status_screen = <!-- The display is working? --> | | status_screen = P <!-- The display is working? --> | ||
| status_wifi = <!-- Wireless network works? --> | | status_wifi = N <!-- Wireless network works? --> | ||
| status_xwayland = <!-- Showing X11 applications in a Wayland compositor (Weston, KWin, ...) works? --> | | status_xwayland = <!-- Showing X11 applications in a Wayland compositor (Weston, KWin, ...) works? --> | ||
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? --> | | status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? --> | ||
| status_mainline = N | | status_mainline = N | ||
| status_battery = <!-- Charging the battery with charging-sdl is possible --> | | status_battery = <!-- Charging the battery with charging-sdl is possible --> | ||
| status_3d = <!-- Hardware accelerated 3D graphics (e.g. with freedreno) --> | | status_3d = N <!-- Hardware accelerated 3D graphics (e.g. with freedreno) --> | ||
| status_accel = <!-- The sensor that measures proper acceleration works --> | | status_accel = <!-- The sensor that measures proper acceleration works --> | ||
| status_audio = <!-- Using the device's speakers/headphone jack works --> | | status_audio = <!-- Using the device's speakers/headphone jack works --> | ||
Line 30: | Line 30: | ||
| status_camera = <!-- Taking photos and videos works. --> | | status_camera = <!-- Taking photos and videos works. --> | ||
| status_gps = <!-- The Global Positioning System sensor works. --> | | status_gps = <!-- The Global Positioning System sensor works. --> | ||
| status_mobiledata = <!-- Connecting to the Internet via cellular network. --> | | status_mobiledata = N <!-- Connecting to the Internet via cellular network. --> | ||
| status_sms = <!-- Sending and receiving short messages works as intended. --> | | status_sms = N <!-- Sending and receiving short messages works as intended. --> | ||
| status_calls = <!-- Talking to other people over the cellular network. --> | | status_calls = N <!-- Talking to other people over the cellular network. --> | ||
| status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" --> | | status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" --> | ||
| status_otg = <!-- USB-OTG adapters work, e.g. to connect an USB flash drive to the device --> | | status_otg = <!-- USB-OTG adapters work, e.g. to connect an USB flash drive to the device --> | ||
Line 53: | Line 53: | ||
== Installation == | == Installation == | ||
You have to do an sdcard install since there doesn't seem to be any partition large enough for <code>pmbootstrap flasher</code>. | |||
Make sure you have an unlocked bootloader. If not, Installation will not be possible. See [[Bootloader#Huawei]] for information on how to unlock it. | Make sure you have an unlocked bootloader. If not, Installation will not be possible. See [[Bootloader#Huawei]] for information on how to unlock it. | ||
== Status table explanation == | |||
{|class="wikitable feature-colors" | |||
|- | |||
! Component !! Status !! Notes | |||
|- | |||
| Flashing || P || Flashing the kernel works, flashing the rootfs doesn't (Use sdcard install) | |||
|- | |||
| Display || P || Splash screen works. Wayland compositors sometimes show up, but the screen flickers on and off. Xorg doesn't work at all. | |||
|} | |||
== See also == | == See also == |
Revision as of 22:43, 21 April 2022
![]() Huawei Ascend G330 running LineageOS 13 | |
Manufacturer | Huawei |
---|---|
Name | Ascend G330 |
Codename | huawei-u8825 |
Released | 2012 |
Hardware | |
Chipset | Qualcomm MSM8225 Snapdragon S4 Play |
CPU | Dual-core 1.0 GHz Cortex-A5 |
GPU | Adreno 203 |
Display | 480x800 IPS |
Storage | 4GB |
Memory | 512 MB |
Architecture | armv7 |
Software | |
Original software | Android 4.0.4 |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | no |
Flashing |
Partial |
---|---|
USB Networking |
Works |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
Partial |
Touchscreen |
Broken |
Multimedia | |
3D Acceleration |
Broken |
Audio |
No data |
Camera |
No data |
Camera Flash |
No data |
Connectivity | |
WiFi |
Broken |
Bluetooth |
No data |
GPS |
No data |
Modem | |
Calls |
Broken |
SMS |
Broken |
Mobile data |
Broken |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
Contributors
- Bastindo
Users owning this device
- Bastindo (Notes: Bootloader unlocked)
How to enter flash mode
- Fastboot: Hold
fastboot devices
+ for 10 seconds on boot. The device will not show any signs of being in fastboot mode (It'll just show the Huawei logo), so you should check with - This device has a locked bootloader, see Bootloader#Huawei
Installation
You have to do an sdcard install since there doesn't seem to be any partition large enough for pmbootstrap flasher
.
Make sure you have an unlocked bootloader. If not, Installation will not be possible. See Bootloader#Huawei for information on how to unlock it.
Status table explanation
Component | Status | Notes |
---|---|---|
Flashing | P | Flashing the kernel works, flashing the rootfs doesn't (Use sdcard install) |
Display | P | Splash screen works. Wayland compositors sometimes show up, but the screen flickers on and off. Xorg doesn't work at all. |
See also