Jump to content

Huawei Ascend G330 (huawei-u8825): Difference between revisions

From postmarketOS Wiki
Bastindo (talk | contribs)
add hwtest results
Bastindo (talk | contribs)
update status table
Line 15: Line 15:
| architecture = armv7
| architecture = armv7
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) -->
<!-- the following status_* questions should be answered with Y - yes, P - partial, N - no, or left blank (for untested or unknown) -->
| status_usbnet = Y <!-- USB networking does work? then put Y here and delete this comment -->
| status_usbnet = Y  
| status_flashing = P<!-- Flashing with "pmbootstrap flasher" works? Put Y here. It works the same for everything coming below. -->
| status_flashing = P
| status_touch = N <!-- Touch screen is working? You can also answer these questions with P for partially. -->
| status_touch = N  
| status_screen = P <!-- The display is working? -->
| status_screen = P  
| status_wifi = N <!-- Wireless network works? -->
| status_wifi = N  
| status_xwayland = <!-- Showing X11 applications in a Wayland compositor (Weston, KWin, ...) works? -->
| status_xwayland =  
| status_fde = <!-- When installing with full disk encryption, can you type in the password with the on screen keyboard? -->
| status_fde =  
| status_mainline = N
| status_mainline = N
| status_battery = <!-- Charging the battery with charging-sdl is possible -->
| status_battery =  
| status_3d = N <!-- Hardware accelerated 3D graphics (e.g. with freedreno) -->
| status_3d = N  
| status_accel = <!-- The sensor that measures proper acceleration works -->
| status_accel =  
| status_audio = <!-- Using the device's speakers/headphone jack works -->
| status_audio = Y
| status_bluetooth = <!-- It's possible to pair and use other devices via the bluetooth protocol -->
| status_bluetooth =  
| status_camera = <!-- Taking photos and videos works. -->
| status_camera =  
| status_gps = <!-- The Global Positioning System sensor works.  -->
| status_gps =  
| status_mobiledata = N <!-- Connecting to the Internet via cellular network. -->
| status_mobiledata = N  
| status_sms = N <!-- Sending and receiving short messages works as intended. -->
| status_sms = N  
| status_calls = N <!-- Talking to other people over the cellular network. -->
| status_calls = N  
| status = <!-- Text displayed in the "not booting" table on the Devices page , e.g "kernel compiles, doesn't boot" -->
| status =  
| status_otg = <!-- USB-OTG adapters work, e.g. to connect an USB flash drive to the device -->
| status_otg =  
| status_nfc = -
| status_nfc = -
| status_irtx = -
| status_irtx = -
| status_usba = -
| status_hdmidp = -
| status_keyboard = -
| status_touchpad = -
| status_magnet =
| status_light =
| status_proximity =
| status_barometer =
| status_powersensor =
| status_trustzone =
| status_fossbootloader = -
| booting = yes
| booting = yes
}}
}}

Revision as of 21:33, 2 August 2022

Huawei Ascend G330
Huawei Ascend G330 running LineageOS 13
Huawei Ascend G330 running LineageOS 13
Manufacturer Huawei
Name Ascend G330
Codename huawei-u8825
Released 2012
Hardware
Chipset Qualcomm MSM8225 Snapdragon S4 Play
CPU Dual-core 1.0 GHz Cortex-A5
GPU Adreno 203
Display 480x800 IPS
Storage 4GB
Memory 512 MB
Architecture armv7
Software
Original software Android 4.0.4
postmarketOS
Category testing
Pre-built images no
Mainline no
Features
Flashing
Partial
USB Networking
Works
Internal storage
No data
SD card
No data
Battery
No data
Screen
Partial
Touchscreen
Broken
Multimedia
3D Acceleration
Broken
Audio
Works
Camera
No data
Camera Flash
No data
Connectivity
WiFi
Broken
Bluetooth
No data
GPS
No data
Modem
Calls
Broken
SMS
Broken
Mobile data
Broken
Miscellaneous
FDE
No data
USB OTG
No data
Sensors
Accelerometer
No data
Magnetometer
No data
Ambient Light
No data
Proximity
No data
Hall Effect
No data
Haptics
No data
Barometer
No data
Power Sensor
No data


Contributors

  • Bastindo

Users owning this device


How to enter flash mode

  • Fastboot: Hold Power + Volume Down for 10 seconds on boot. The device will not show any signs of being in fastboot mode (It'll just show the Huawei logo), so you should check with fastboot devices
  • This device has a locked bootloader, see Bootloader#Huawei

Installation

You have to do an sdcard install since there doesn't seem to be any partition large enough for pmbootstrap flasher.

Make sure you have an unlocked bootloader. If not, Installation will not be possible. See Bootloader#Huawei for information on how to unlock it.

Status table explanation

Component Status Notes
Flashing P Flashing the kernel works, flashing the rootfs doesn't (Use sdcard install)
Display P Splash screen works. Wayland compositors sometimes show up, but the screen flickers on and off. Xorg doesn't work at all.

hwtest

Category         Model                Path                                                                                            Status     Value
framebuffer      msmfb303_90000       /sys/class/graphics/fb0                                                                         working    U:480x800p-0
input            ts_test_input        /dev/input/event5                                                                               working    
input            7k_handset           /dev/input/event4                                                                               working    
input            sensors_aps          /dev/input/event3                                                                               working    
input            default_keypad       /dev/input/event2                                                                               working    
input            sensors              /dev/input/event1                                                                               working    
input            synaptics            /dev/input/event0                                                                               working    
speaker          default:CARD=msmaudio                                                                                                 working    
mic              default:CARD=msmaudio                                                                                                 working

See also