Xiaomi POCO M2 Pro / Redmi Note 9S / Redmi Note 9 Pro / Redmi Note 9 Pro Max / Redmi Note 10 Lite (xiaomi-miatoll)
Appearance
![]() Xiaomi Redmi Note 9 Pro (xiaomi-joyeuse) with aftermarket display | |
Manufacturer | Xiaomi |
---|---|
Name |
POCO M2 Pro / Redmi Note 9S / Redmi Note 9 Pro / Redmi Note 9 Pro Max |
Codename | xiaomi-miatoll |
Released | 2020 |
Hardware | |
Chipset | Qualcomm Snapdragon 720G (SM7125) |
CPU | Octa-core (2x2.3 GHz Kryo 465 Gold & 6x1.8 GHz Kryo 465 Silver) |
GPU | Adreno 618 |
Display | 1080 x 2400 (IPS LCD, 6.67") |
Storage | 64/128 GB |
Memory | 4/6 GB |
Architecture | aarch64 |
Software | |
Original software | Android |
Original version | 10 (MIUI 11) |
postmarketOS | |
Category | testing |
Pre-built images | no |
Mainline | partial |
Flashing |
Works |
---|---|
USB Networking |
Works |
Internal storage |
No data |
SD card |
No data |
Battery |
No data |
Screen |
Works |
Touchscreen |
No data |
Multimedia | |
3D Acceleration |
No data |
Audio |
No data |
Camera |
No data |
Camera Flash |
No data |
IR TX |
No data |
Connectivity | |
WiFi |
Works |
Bluetooth |
No data |
GPS |
No data |
NFC |
No data |
Modem | |
Calls |
No data |
SMS |
No data |
Mobile data |
No data |
Miscellaneous | |
FDE |
No data |
USB OTG |
No data |
HDMI/DP |
No data |
Sensors | |
Accelerometer |
No data |
Magnetometer |
No data |
Ambient Light |
No data |
Proximity |
No data |
Hall Effect |
No data |
Haptics |
No data |
Barometer |
No data |
This device is based on the Qualcomm Snapdragon 720G (SM7125). See the SoC page for common tips, guides and troubleshooting steps |
Contributors
Users owning this device
- Bczeman
- Imre (Notes: stock rom, daily driver)
- ItsVixano
- Jojo autoboy (Notes: Main device, Redmi Note 9S (curtana) variant)
- Lassebq (Notes: Currently running LineageOS)
- Latenightdef (Notes: Running LineageOS)
- Miki (Notes: secondary/fuckery device)
- Nikroks (Notes: Mainline maintainer)
- Omame (Notes: daily driver)
- Projjal
- Sado1
- Selfisekai (Notes: held by polish law enforcement)
- Somekool (Notes: Currently running PixysOS)
- Ungeskriptet (Notes: Working on upstreaming SM7125 support)
- Zekiu (Notes: xiaomi-joyeuse)
How to enter flash mode
- Fastboot: Power on the device with both and buttons.
- Recovery: Power on the device with both and buttons.
EDL Mode
Note: An authenticated Mi account for EDL flashing is required. |
To enter the EDL mode, disconnect the battery and short these two points while powering it on with USB. If lsusb -d 05c6:9008
shows you a device, you can let go of the short.
UART
The UART points are located on the front on the mainboard, so thin wires should be soldered to the tiny test points to route them to the back.
Installation
/* Not yet */